﻿================================================================================
Express5800/R110m-1M
System ROM U71 v1.44 (07/11/2025)
================================================================================
Software name    : Express5800/R110m-1M
                   System ROM (BIOS) update module
Models           : Express5800/R110m-1M
Operating System : Windows Server(R) 2022
                   Windows Server(R) 2025
Method of update : Firmware update via the iLO web interface
Target Users     : See [Target Users for Update] below
Type             : System ROM
================================================================================


[About the software]
The Express5800/R110m-1M System ROM (BIOS) update module supports the following
changes in the Express5800/R110m-1M models:

 Enhancements and problem fixes:
 - Initial release.

  ** Program and data included in this software **
 Following program and data are included in this software.
 Use one of them according to the way of installation.

  a) Flash Firmware Package for iLO Web User Interface
      firmware\OEM.U68_1.44_07_11_2025.fwpkg

-------------------------------------------------------------------------------
[ Target Users for Update ]
This software is available for the users who use the following models with the
following System ROM version.

  - Models to be supported

     1. Express5800/R110m-1M

  - System ROM Versions to be supported

     - Initial release.


Note: In case of using newer System ROM from the above version, it has already
      applied equivalent enhancements. Updating the System ROM isn't needed.

Be sure to check the System ROM version and date with the following procedures.
Select an arbitrary procedure and check the version before and after the update.

 ** System Utilities **

 You can check the System ROM version and date by the following procedure.

    1. Power on the system and the contents of process by POST (Power On Self-
       Test) will be shown on the screen. After a short time, the following
       message is shown. Press <F9> key, "System Utilities" is started.

                        [F9] System Utilities

    2. After starting "System Utilities", select "System Information".

    3. Select "Firmware Information".

    4. Each firmware version is shown on the screen. The System ROM version and
       date can be seen at "System ROM" option.

  Note: After checking the System ROM version, press the <ESC> key or
        select "Exit" to exit the System Utilities.

  Note: About detail of "System Utilities" usage, refer to "1. System
        Utilities" section in the chapter of "Useful Features" of the
        maintenance guide.

 ** Windows(R) OS **

 You can check the System ROM date by a following procedure.

    1. Hold down <Windows> key and press <R> key.

    2. In the "Run" dialog box, type "msinfo32" and then click "OK".

    3. After "System Information" has started, select "System Summary".

    4. Check the System ROM version by the profile of "BIOS Version/Date".

================================================================================
 System ROM Installation Procedure
================================================================================

  1. Preparation of Flash Firmware Package for iLO Web User Interface (*.fwpkg)

   (1) Copy "a) Flash Firmware Package for iLO Web User Interface file"
       (i.e. *.fwpkg) to any location which is accessible from the remote PC.

  2. System ROM installation procedure

   (1) Start the Web Browser on remote PC. And log-in to the iLO Web User
       Interface by a "Configure to iLO Settings" privilege user.

   (2) Select "Firmware tab" from the right menu.

   (3) Select "Update Firmware" from the left menu.

   (4) Select the Flash Firmware Package for iLO Web User Interface,
       copied by a procedure of "1."

   (5) Press "Update" to begin update process.

   (6) Wait for the "Firmware Update Completed." message to display.

   (7) Reboot the system.

   (8) Wait reboot completion for update to take effect.

     The installation is successfully finished.


================================================================================
 Notes
================================================================================
  ** Notes in general **

  * Refer to "license_en.txt" about the user license agreement.

  * When Windows(R) BitLocker(TM) function is set to "Enabled", install the
    System ROM after making the function "Disabled". Then make the function
    "Enabled" after install and reboot of the system. If you install the system
    ROM without making the function "Disabled", you may need the recovery
    password when you boot the system.

  * To meet firmware dependencies, you can update iLO7 firmware by latest
    Starter Pack. 
    You can download latest update module(s) from the following web site.
    https://www.nec.com/express
    ("Support & Downloads" of the page top - PCs & Servers - Servers - Downloads
    - Select Model)


--------------------------------------------------------------------------------
[Revision history]
Version:1.44 (07/11/2025)

 Enhancements and problem fixes:
 - Initial release.

--------------------------------------------------------------------------------
[Copyright and Trademark]

All contents on this software are the copyright of NEC Corporation or the
third-party software developer. All other contents mentioned herein are
copyright of their respective owners.

Microsoft, Windows, Windows Server are trademarks or registered trademarks of
Microsoft Corporation in the United States and other countries.

All other company names and product names mentioned herein are registered
trademarks or trademarks of their respective owners.

--------------------------------------------------------------------------------
   Copyright NEC Corporation 2023
