================================================================================
Express5800/T110k
Express5800/T110k-S
iStorage NS100Tk
System BIOS F18
================================================================================
Software Name    : System BIOS update module for Express5800/T110k,
                   Express5800/T110k-S, and iStorage NS100Tk
Models           : Express5800/T110k, Express5800/T110k-S, and iStorage NS100Tk
Operating System : This software supports offline updates (with a CD/DVD medium)
                   and updates on the following OSs:
                   - Windows Server(R) 2019
                   - Windows Server(R) 2022
                   - Red Hat(R) Enterprise Linux(R) 8
Target Users     : See "Target users for the update" below
Type             : System BIOS
================================================================================

[ About the Software ]
This "System BIOS update module for Express5800/T110k, Express5800/T110k-S, and
iStorage NS100Tk (hereafter referred to as 'this software')" is intended for the
following security improvements and bug fixes:

  - Addressed security vulnerabilities:
    - Updated the microcode for Intel(R) Xeon(R) E processors to mitigate the
      INTEL-SA-01396 and INTEL-SA-01423 vulnerabilities.
    - Mitigated the OpenSSL security vulnerabilities. This includes the
      following CVEs:
        CVE-2025-15467, CVE-2025-68160, CVE-2025-69418, CVE-2025-69419,
        CVE-2025-69421, CVE-2026-22795, CVE-2026-22796, CVE-2025-11187
    - Mitigated the Intel distribution code security vulnerabilities. This
      includes the following CVEs:
        CVE-2025-58771, CVE-2025-58772, CVE-2025-58773, CVE-2025-58774

  - Added new Secure Boot keys.
      No special configuration or operation is required for this addition in
      environments that are already using Secure Boot.
      Note:
        If the BitLocker(TM) feature is enabled, do not perform any of the
        following Secure Boot key operations. If any of these operations are
        performed, the system will need to enter the recovery key at system
        startup. If the recovery key is not kept, Windows(R) OS will not be
        able to start. It is recommended to keep the recovery key in a safe
        place.
        - Change the configuration from "Custom" to "Standard" in the
          "Security" -> "Secure Boot Configuration" -> "Secure Boot Mode" and
          press "Yes" when "Install factory defaults" is displayed.
        - Execute the menu of "Enroll All Factory Default Keys" in the
          "Security" -> "Secure Boot Configuration" -> "Enroll All Factory
          Default Keys" and press "Yes" when "Install factory defaults" is
          displayed.
        - Execute the menu of "Enroll All Factory Default Keys" in the
          "Security" -> "Secure Boot Configuration" -> "Key Management" ->
          "Enroll All Factory Default Keys" and press "Yes" when "Install
          factory defaults" is displayed.

  - Fixed an issue in which a BSoD (Blue Screen of Death) occurred during
    startup of Windows Server(R) when all of the following conditions were met:
    - The system was equipped with an Intel(R) Pentium(R) Gold Processor Series.
    - System BIOS version F09 or later was used.
    - "Intel(R) Speed Shift Technology" was set to "Out of Band Mode" under
      "Advanced" -> "Power & Performance" -> "CPU - Power Management Control"
      in the BIOS Setup Utility.

  - Resolved an issue that caused the following error message to appear
    during startup of Red Hat(R) Enterprise Linux(R) 8.7 or later when all
    of the following conditions were met:
    - The system was equipped with an Intel(R) Xeon(R) E processor.
    - System BIOS version F09 or later was used.
    - "Intel(R) Speed Shift Technology" was set to "Out of Band Mode" under
      "Advanced" -> "Power & Performance" -> "CPU - Power Management Control"
      in the BIOS Setup Utility:

      Needed type [Reference], found [Buffer] XXXXXXXXXXXXXXXX
      AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable]
      Aborting method \_SB.PR00._CPC due to previous error (AE_AML_OPERAND_TYPE)

    Note: While this message would display on screen, it did not impact system
          operation. The fix ensures this message will no longer appear.
          "XXXXXXXXXXXXXXXX" indicates the memory address of the Buffer. This
          address varies depending on the system configuration and the memory
          layout at startup.

  ** Important Notes Before Update **

  - Before applying this system BIOS, BMC firmware revision 01.16 or later is
    required. There are no restrictions on the order of applying the system
    BIOS and BMC firmware, but if using system BIOS version F06 or earlier,
    apply BMC firmware revision 01.16 or later in advance.
    The latest BMC firmware can be downloaded from the following web page:
    https://www.support.nec.co.jp/View.aspx?id=9010110053
    To check the BMC firmware revision, refer to the manual attached to the BMC
    firmware update module.

  - Do not perform the following operation in the BIOS Setup Utility. If you
    execute this operation, you might delete the latest Secure Boot Key provided
    by Microsoft.

    - Change the configuration from "Custom" to "Standard" in the "Security"
      -> "Secure Boot Configuration" -> "Secure Boot Mode" and press "Yes" when
      "Install factory defaults" is displayed.

    - Execute the menu of "Enroll All Factory Default Keys" in the "Security"
      -> "Secure Boot Configuration" -> "Enroll All Factory Default Keys" and
      press "Yes" when "Install factory defaults" is displayed.

    - Execute the menu of "Enroll All Factory Default Keys" in the "Security"
      -> "Secure Boot Configuration" -> "Key Management" -> "Enroll All Factory
      Default Keys" and press "Yes" when "Install factory defaults" is
      displayed.

  ** Cautions in General **

  * An incorrect update could result in a failure, such as the system fails to
    boot. For a successful update, read through this document carefully and
    follow the instructions.
    Should your system malfunction or be powered off due to an unplanned event
    (such as a blackout, a cutoff, lightning and noise) during the update, the
    system may be damaged and fail to operate normally.  In such a case, the
    system may need to be repaired at your expense.

  * When the Windows(R) BitLocker(TM) feature is enabled, disable it before the
    update. After the update is completed, enable the feature again. Without
    disabling the feature before the update, booting the system may require the
    recovery key.

--------------------------------------------------------------------------------
[ Target Users for the Update ]
The Software is available for customers using the following models with the
following BIOS version.

  - Supported models
     1. Express5800/T110k
     2. Express5800/T110k-S
     3. iStorage NS100Tk

  - Supported BIOS versions
     1. F04
     2. F05
     3. F06
     4. F09
     5. F10
     6. F11
     7. F12
     8. F13
     9. F14
    10. F15
    11. F16
    12. F17

Note: This update is not necessary if the above BIOS versions are earlier than
      yours, as your BIOS version already includes the equivalent enhancements
      and modifications to be added by the Software.

Your system BIOS version can be checked in any of the following ways:

 <On BIOS Setup Utility>
    1. Power on the system, and then the screen shows the process of the POST
       (Power On Self-Test). After a short time, the following message appears:

                        Press <F2> SETUP

       Then press the F2 key to start BIOS Setup Utility.

    2. The "Main" menu shows your BIOS version.

  Note: To exit BIOS SETUP Utility, move the cursor with the left or right key
        to the position of "Save & Exit" and then select "Discard Changes and
        Exit."

  Note: For details on how to use BIOS SETUP Utility, refer to "Details of
        System BIOS" in the chapter of "Useful Features" in the maintenance
        guide.

 <On the Windows(R) OS>
    1. Hold down the Windows key and press the R key.

    2. In the "Run" dialog box, type "msinfo32" and then click "OK."

    3. After the "System Information" window opens, select "System Summary."

    4. Check the "BIOS Version/Date" item to find your BIOS version.

 <On the Linux(R) OS>
    1. Start a terminal emulator such as xterm.

    2. Execute the following command:
        # /usr/sbin/dmidecode | less

       Note: The # means a prompt. You do not need to input this symbol.

    3. Check the BIOS Information->Version item to find your BIOS version.

       Note: The dmidecode command has to be installed in advance.

================================================================================
 System BIOS Update Procedure
================================================================================

** To Update the BIOS Offline **

  Prepare a writable CD/DVD medium.

  1) Creation of Installation Medium
     Download and unzip the zipped file to extract the file of
     BIOS_F18_updatetool.iso.
     Burn the iso file onto the CD/DVD medium with a burning
     software.
     This CD/DVD medium is the "System BIOS update module" medium.
     For details on the burning procedure, refer to the manual of the burning
     software.

     Name the CD/DVD medium as follows and keep it:

            Express5800/XXX
               (N8YYY-YYY)
            BIOSVERSION ZZZ
        System BIOS update module

     or,
            iStorage NS100Tk
               (NF8YYY-YYY)
            BIOSVERSION ZZZ
        System BIOS update module

     Note: These XXX, YYY and ZZZ mean the model name, the part number of your
           system and the system BIOS version respectively.

  2) Preparation for the Update

     1. Confirm that "Secure Boot" is set at "Disabled" (factory setting).
        If "Secure Boot" is set at "Enabled", the system BIOS cannot be updated.

        The setting of "Secure Boot" can be checked as follows:
          a. Following the message, "Press <F2> SETUP", during the 
             POST, press the F2 key to start BIOS Setup Utility.

          b. From the "Security" menu, select the "Secure Boot Configuration"
             submenu.

          c. Confirm the setting of "Secure Boot".

        If "Enabled" is set, change it to "Disabled" before updating the system
        BIOS. After the update is completed, set "Enabled" again.

  3) System BIOS Update Procedure
     Update the system BIOS by following the procedure below:

     Note: During this system BIOS update (offline), do not press any key except
           one in Step 7 below. If you press the Scroll Lock key or the Pause/
           Break key during the system BIOS update, the update process stops. In
           this case, press the same key again to resume the update process.

     1. Power on the system.

     2. Insert the "System BIOS update module" medium created in the 1) Creation
        of Installation Medium into the CD/DVD drive of the system.

     3. The following menu appears after CD/DVD is read:

        BIOS Update Tool (Version: Fxx)

        Note: The xx means a BIOS version to be updated to.

     4. Before the system BIOS update starts, the following message appears:

        loading ...

        Note: Trying to update it displays the following message:
               - Check RomLayout .................. Fail
               WARNING !!
                Command /RLC: (assigned a default option) has the potential risk
               to
                crash system if users have no clear BIOS flash information.
              <Press any key to cancel or waiting 05 seconds to continue.>

              However, ignore this message. It is due to the intended
              modification supported by version F13 of the system BIOS update
              module. Following the message does not cancel the update.

     5. After the system BIOS update is completed, the following message
        appears:

        **********************************************
        Executing shell script has been completed.
        Press <Enter> key to shut down.
        **********************************************

        Note: If an error or warning message other than the above appears,
              refer to "Notes on the Offline Update" below.

     6. Eject the CD/DVD medium from the drive.

     7. Press the Enter key to shut down the system.

     8. Power on the system again.

     9. Check that the BIOS version is shown as Fxx.

        Note: The xx means a BIOS version to be updated to.

     Now the update is successfully finished.

** To Update the BIOS on the Windows(R) OS **

  1) Preparation for the Update

     1. Log in to the system as an administrator.

     2. Close all the running applications.

     3. Download and unzip the ZIP package of the Software into any directory of
        the hard disk.

  2) System BIOS Update Procedure

     1. Right-click a Command Prompt and select "Run as administrator", and run
        the following command to start the system BIOS update program:
        # WinBIOSUpdate.bat
        Then follow the displayed messages.

     2. The following message appears before the system BIOS update starts:

        ************* Execute BIOS Update *************
        The update process will take approximately 2 to 3 minutes.
        DO NOT power off the system during this update process.

     3. When the system BIOS update succeeds, the following message appears:

        BIOS update process has completed.
        Please restart your computer now to enable update.
        Do you want to restart your computer now?
        [yes/no]

        If you type yes and then press the Enter key, the system is rebooted.

        Note: If you type no, the system is not restarted. The subsequent
              operation of the system is not guaranteed. Reboot the system 
              promptly.

        Note: If an error or warning message other than the above appears,
              refer to "Notes on the Update on the Windows(R)/Linux(R) OS"
              below.

     4. After the system is rebooted, check that the BIOS version is shown as 
        Fxx.

        Note: The xx means a BIOS version to be updated to.

     Now the update is successfully finished.

** To Update the BIOS on the Linux(R) OS **

  1) Preparation for the Update

     1. Confirm that "Secure Boot" is set at "Disabled" (factory setting).
        If "Secure Boot" is set at "Enabled", the system BIOS cannot be updated.

        The setting of "Secure Boot" can be checked as follows:
          a. Following the message, "Press <F2> SETUP", during the 
             POST, press the F2 key to start BIOS Setup Utility.

          b. From the "Security" menu, select the "Secure Boot" submenu.

          c. Confirm the setting of "Secure Boot".

        If "Enabled" is set, change it to "Disabled" before updating the system
        BIOS. After the update is completed, set "Enabled" again.

     2. Use the su command to become the root user.

     3. Close all the running applications.

     4. Download and unzip the ZIP package of the Software into any directory
        of the hard disk.
        Move to the directory into which you extracted the module.

  2) System BIOS Update Procedure

     1. Run the following command to start the system BIOS update program:
        # bash ./LinuxBIOSUpdate.sh
        Then follow the displayed messages.

     2. The following message appears before the system BIOS update starts:

        ************* Execute BIOS Update *************
        The update process will take approximately 2 to 3 minutes.
        DO NOT power off the system during this update process.

     3. When the system BIOS update succeeds, the following message appears:

        ****************************************************
         BIOS update process has completed.                 
         Please restart your computer now to enable update. 
         Do you want to restart your computer now?          
         [yes/no]                                           
        ****************************************************

        If you type yes and then press the Enter key, the system is rebooted.

        Note: If you type no, the system is not restarted. The subsequent
              operation of the system is not guaranteed. Reboot the system
              promptly.

        Note: If an error or warning message other than the above appears,
              refer to "Notes on the Update on the Windows(R)/Linux(R) OS"
              below.

     4. After the system is rebooted, check that the BIOS version is shown as
        Fxx.

        Note: The xx means a BIOS version to be updated to.

     Now the update is successfully finished.

================================================================================
 Notice
================================================================================
- Notes on the Offline Update
During the system BIOS update, any of the following messages may appear:

   (a) BIOS version is incorrect

       This message indicates that the current system BIOS version is the same
       as the version being applied or newer. Therefore, this update is not
       necessary. Refer to "Supported BIOS versions" above.

   (b) Platform mismatch

       This message appears when you proceed with an unsupported model.
       Refer to "Supported models" above.

   (c) WARNING : System must power-off to have the changes take effect!

       No problem exists since this update procedure turns off the system.

   Note: If an error or warning message other than the above appears, contact
         your sales representative.

- Notes on the Update on the Windows(R)/Linux(R) OS
During the system BIOS update, the following message may appear:

   (a) Error Code: 1001
       This message appears when you try to apply the update to an inapplicable
       model. Refer to "Supported models" and "Supported BIOS versions" above.

   Note: If an error or warning message other than the above appears, contact
         your sales representative.

- Note on Terms and Conditions of Use
The licensed software may contain components licensed to you under different 
license agreements. In this case, the terms and conditions of the agreements 
for using the components shall prevail over those of this license agreement.

-------------------------------------------------------------------------------
[ Revision History ]
11/17/2026   F18
- Addressed security vulnerabilities:
  - Updated the microcode for Intel(R) Xeon(R) E processors to mitigate the
    INTEL-SA-01396 and INTEL-SA-01423 vulnerabilities.
  - Mitigated the OpenSSL security vulnerabilities. This includes the following
    CVEs:
      CVE-2025-15467, CVE-2025-68160, CVE-2025-69418, CVE-2025-69419,
      CVE-2025-69421, CVE-2026-22795, CVE-2026-22796, CVE-2025-11187
  - Mitigated the Intel distribution code security vulnerabilities. This
    includes the following CVEs:
      CVE-2025-58771, CVE-2025-58772, CVE-2025-58773, CVE-2025-58774

- Added new Secure Boot keys.
    No special configuration or operation is required for this addition in
    environments that are already using Secure Boot.
    Note:
      If the BitLocker(TM) feature is enabled, do not perform any of the
      following Secure Boot key operations. If any of these operations are
      performed, the system will need to enter the recovery key at system
      startup. If the recovery key is not kept, Windows(R) OS will not be
      able to start. It is recommended to keep the recovery key in a safe
      place.
      - Change the configuration from "Custom" to "Standard" in the
        "Security" -> "Secure Boot Configuration" -> "Secure Boot Mode" and
        press "Yes" when "Install factory defaults" is displayed.
      - Execute the menu of "Enroll All Factory Default Keys" in the
        "Security" -> "Secure Boot Configuration" -> "Enroll All Factory
        Default Keys" and press "Yes" when "Install factory defaults" is
        displayed.
      - Execute the menu of "Enroll All Factory Default Keys" in the
        "Security" -> "Secure Boot Configuration" -> "Key Management" ->
        "Enroll All Factory Default Keys" and press "Yes" when "Install
        factory defaults" is displayed.

- Fixed an issue in which a BSoD (Blue Screen of Death) occurred during
  startup of Windows Server(R) when all of the following conditions were met:
  - The system was equipped with an Intel(R) Pentium(R) Gold Processor Series.
  - System BIOS version F09 or later was used.
  - "Intel(R) Speed Shift Technology" was set to "Out of Band Mode" under
    "Advanced" -> "Power & Performance" -> "CPU - Power Management Control"
    in the BIOS Setup Utility.

- Resolved an issue that caused the following error message to appear
  during startup of Red Hat(R) Enterprise Linux(R) 8.7 or later when all
  of the following conditions were met:
  - The system was equipped with an Intel(R) Xeon(R) E processor.
  - System BIOS version F09 or later was used.
  - "Intel(R) Speed Shift Technology" was set to "Out of Band Mode" under
    "Advanced" -> "Power & Performance" -> "CPU - Power Management Control"
    in the BIOS Setup Utility:

    Needed type [Reference], found [Buffer] XXXXXXXXXXXXXXXX
    AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable]
    Aborting method \_SB.PR00._CPC due to previous error (AE_AML_OPERAND_TYPE)

  Note: While this message would display on screen, it did not impact system
        operation. The fix ensures this message will no longer appear.
        "XXXXXXXXXXXXXXXX" indicates the memory address of the Buffer. This
        address varies depending on the system configuration and the memory
        layout at startup.

11/14/2025   F17
- Addressed security vulnerabilities:
  - Updated the microcode for Intel(R) Xeon(R) E processors and Intel(R)
    Pentium(R) Gold Processor Series to mitigate the INTEL-SA-01153,
    INTEL-SA-01213 and INTEL-SA-01247 vulnerabilities.
  - Updated Intel SPS firmware to version 6.0.3.708 to mitigate the
    INTEL-SA-00718 vulnerability.
  - Mitigated the OpenSSL security vulnerabilities. This includes the
    following CVEs:
      CVE-2023-52353, CVE-2024-9143, CVE-2023-6237, CVE-2024-6119,
      CVE-2024-5535, CVE-2024-13176
  - Mitigated the SmiFlash race condition vulnerability. This includes the
    following CVEs:
      CVE-2025-22830
  - Mitigated the Intel distribution code security vulnerabilities. This
    includes the following CVEs:
      CVE-2025-20027, CVE-2025-20028

- Fixed the issue the following error message would appear during OS boot on
  Red Hat(R) Enterprise Linux(R) 8.8 or later when equipped with the
  Intel(R) Pentium(R) Gold Processor Series:
    Could not resolve symbol [\_SB.PC00.PGOF.PBGE]
  Note: While this message would display on screen, it did not impact system
        operation. The fix ensures this message will no longer appear.

01/27/2025   F16
- Addressed security vulnerabilities:
  - Mitigated the hardware initialization code vulnerabilities
    (INTEL-SA-00813) and other security vulnerabilities (CVE-2022-31600,
    CVE-2023-28005, CVE-2023-34470) notified by Intel.
  - Updated the microcode for Intel(R) Xeon(R) E processors and Intel(R)
    Pentium(R) Gold Processor Series to mitigate INTEL-SA-00828 and
    INTEL-SA-00950 vulnerabilities.
  - Mitigated vulnerabilities collectively known as LogoFAIL (CVE-2023-39538,
    CVE-2023-39539).
  - Mitigated vulnerabilities in the EDK2 NetworkPkg IP stack implementation.
    This includes the following CVEs:
      CVE-2023-45229, CVE-2023-45230, CVE-2023-45231, CVE-2023-45232,
      CVE-2023-45233, CVE-2023-45234, CVE-2023-45235, CVE-2023-45236, 
      CVE-2023-45237
  - Mitigated vulnerabilities in the TPM2 Measure Boot library
    (CVE-2022-36763, CVE-2022-36764).
  - Mitigated OpenSSL security vulnerabilities. This includes the following
    CVEs:
      CVE-2022-4304, CVE-2022-4450, CVE-2023-0215, CVE-2023-0286,
      CVE-2023-0464, CVE-2023-0465, CVE-2023-2650, CVE-2023-3817

- Updated graphics driver
  - Updated the graphics UEFI driver. This change requires an update to the
    graphics accelerator driver for Windows Server(R). The driver can be
    downloaded from this URL:
     https://www.support.nec.co.jp/View.aspx?id=9010111622

- Improved power control feature
  - The minimum configurable power threshold for the power control feature
    has been increased by 10 watts from the previous setting.
  [Notice]
    Depending on the configuration, power consumption may not decrease to the
    set minimum power threshold. In such cases, a shutdown may occur at
    startup, so settings of 50 watts or more are recommended.

12/27/2023   F15
- Fixed the following issue in earlier versions of the system BIOS, F11 to
  F14: After the POWER switch was pressed or the system  was rebooted, it took
  a long time for the POWER indicator to light up.

- Fixed the following issue that had occurred with a correctable or
  uncorrectable memory error: In some cases, memory error events registered in
  the system event log (SEL) indicated non-installed-DIMM numbers.

03/07/2023   F14
- Updated the hardware initialization code to mitigate the security
  vulnerabilities reported in INTEL-SA-00717 released by Intel Corporation.

- Updated the microcode for the following processors, to mitigate the security
  vulnerability reported in INTEL-SA-00767 released by Intel Corporation:
  Intel(R) Xeon(R) E Processor
  Intel(R) Pentium(R) Gold Processor Series

- Updated the Forbidden Signatures(DBX) of Secure Boot keys.

- Fixed the issue of an inability for the DUMP (NMI) switch to work for a
  certain period of time (about one hour) after a system start with "TPM
  Support" (BIOS Setup Utility -> "Advanced" -> "Trusted Computing") set to
  "Enabled".

- Allowed BIOS Setup Utility to detect IO address contention with "Change
  Settings" in "Serial Port 1 Configuration" and "Serial Port 2 Configuration"
  (BIOS Setup Utility -> "Advanced" -> "AST2600 Super IO Configuration") set
  to the same IO address.

- Added the "DMA Control Guarantee" menu.
  "Chipset" -> "System Agent (SA) Configuration": "Enabled" or "Disabled"
  This allows you to enable or disable the Kernel DMA Protection feature.

11/22/2022   F13
- Rearranged the ROM map in the system BIOS, based on the Intel processor
  specification. This change will not affect features used by customers.

- Fixed an issue the uncorecctable errors misdetected over the all DIMMs at
  the startup which causes POST to stop with the following error displayed.
  "AE8xh DIMMx with error is enabled"

10/18/2022   F12
- Fixed the issue of appearing the following C321 POST error on the screen and
  stopping POST when using a N8181-152 Internal simple UPS or N8181-153
  Internal simple UPS Control Kit.
  'POST ERROR C321 System power consumption is out-of-range in BBUs.'

- Fixed the issue which the following menu is not functional for BIOS setup: 
  "Chipset" -> "PCH-IO Configuration" -> "PCI Express Configuration" -> 
  "PCI Express Slot #1" -> "PCIe Speed".

- Fixed the issue which is unable to set the hardware clock using the 'esxcli 
  hardware clock set' command when using the VMware ESXi 6.x / 7.x.

- Updated the microcode for the following processors to mitigate the security
  vulnerabilities reported in INTEL-SA-00615, INTEL-SA-00617, INTEL-SA-00614
  and INTEL-SA-00657 released by Intel Corporation:
  Intel(R) Xeon(R) E Processor
  Intel(R) Pentium(R) Gold Processor Series

- Updated SPS firmware(6.0.3.204) to mitigate the security vulnerabilities
  reported in INTEL-SA-00610.

- Supported the recording IPMI event log when the system power does not 
  decrease below the threshold even after the specified time has passed.

- Fixed the issue that the system may be powered on immediately after
  the system is powered off or the system is shut down from the operating
  system.

07/13/2022   F11
- Fixed the issue of stopped the BMC firmware in the redundant power
  configuration sometimes occurred when you set the option of the "AC-LINK"
  menu (under "Server Mgmt" for BIOS SETUP) to "Last State" or "Power On" and
  then plugged in the server to turn it on.
  - Both STATUS LED 1 and STATUS LED 2 keep lighting.
  - The system's FRU information is changed to default string unexpectedly.
  - The UUID (system ID) is changed unexpectedly.
  - Led to an unauthenticated Windows Server(R) license.
  - Unable to utilize the remote management feature on using the bundled
    software (e.g., NEC ESMPRO Manager) for management PCs.

* By using this software, the following phenomenon was confirmed.
  * Takes 12 seconds for POWER LED to be lit while starting the server either
    by pressing Power button or by rebooting command and the POWER LED might
    remain not lighting for another 12 seconds during POST.
  * BMC firmware revision 01.14 or later resolved the restrictions on redundant
    power configuration and also on the AC-LINK menu which was to be selected
    only "Stay Off" on using the optional N8181-191 PCI FAN.
    Refer to "Useful Features" -> "Details of System BIOS" on the maintenance
    guide for the procedure of changing the option on AC-LINK menu.

06/13/2022   F10
- Fixed the issue of failing to boot from the internal, optical disk drive
  with software RAID (SWRAID) in some cases. This issue sometimes occurred at
  the next startup after you went to "Save & Exit" in BIOS Setup Utility and
  executed "Load Setup Defaults". This fix increases the startup time of the
  system with software RAID by 30 seconds.

03/18/2022   F09
- Enhanced the memory failure detection function. Accordingly, supported the
  following menu for BIOS setup: "Chipset" -> "System Agent (SA)
  Configuration" -> "Memory Configuration" -> "Memory Retest".

- Supported the Intel Trusted Execution Technology feature. Accordingly,
  supported the following menu for BIOS setup: "Advanced" -> "CPU
  Configuration" -> "Intel Trusted Execution Technology".

- Supported the LAN controller function. Accordingly, supported the following
  menu for BIOS setup: "Advanced" -> "PCI Configuration" -> "LAN Controller".

- Supported the HTTP boot function. Accordingly, supported the following menus
  for BIOS setup: "Advanced" -> "Network Stack Configuration" -> "IPv4 HTTP
  Support" and "IPv6 HTTP Support".

- Supported the function to display the POST screen at an early timing.

- Added the function to retain the password that was set on the "Administrator
  Password" and "User Password" menus under "Security" for BIOS setup, when
  NVRAM memory is cleared.

- Fixed the issue of the actual DIMM number being different from the DIMM
  number in the memory information on "Memory" under "System Inventory" on the
  BMC management console.

- Supported the function to detect abnormal values of system's temperature
  and voltage during POST.

- Supported Windows Server (R) 2022.

- Supported Graphics Accelerator N8105-61.

- Supported the power control function.

- Supported Red Hat(R) Enterprise Linux(R) 8.5.

  Applying BMC firmware revision 01.16 or later is required in order to use the
  enhanced functions with System BIOS version F09.

02/11/2022   F06
- Fixed the issue of the OS panic rarely occurring when the Windows OS is
  started up in the configuration using the RAID controller N8103-232.

12/17/2021   F05
- Fixed the issue of an error being detected during POST when remote KVM
  feature is disabled and the system is started with a keyboard and a mouse
  disconnected.

- Supported the memory failure detection function. Accordingly, supported the
  following menu for BIOS setup: "Chipset" -> "System Agent (SA) Configuration"
  -> "Memory Configuration" -> "Memory C-Error Retest".

- Supported the function to detect the PCI Express failure.

- Supported PCI Express expansion boards which equip a particular PCI
  Express-to-PCI Bridge.

- Fixed the issue of "Watchdog Timer times out" being detected if booted from
  a device other than a hard disk drive when other than "Disabled" is set to the
  "Boot Monitoring" menu under "Server Mgmt" for BIOS setup.

--------------------------------------------------------------------------------
[ Copyright and Trademark ]

Microsoft, Windows, and Windows Server are trademarks or registered trademarks
of Microsoft Corporation in the United States and other countries.
Linux(R) is the registered trademark of Linus Torvalds in the United States
and other countries.
Red Hat and Red Hat Enterprise Linux are trademarks or registered trademarks
of Red Hat, Inc. in the United States and other countries.
All other company names and product names mentioned herein are trademarks
or registered trademarks of their respective owners.

The copyright of the Software is owned by NEC Corporation or the third-party
software developer. All other products mentioned herein are copyrighted
works of their respective manufacturers.

--------------------------------------------------------------------------------
   Copyright NEC Corporation 2026