# MegaSAS CLI utility generated ini file for MFC programming.

OEM = 6                        # OEM Name of controller
sasAddress = 50:03:01:30:f0:90:00:00                 # controller SAS address
phyPolarity = 0                # polarity for each possible PHY (bitmap...1=inverted) - used with phyPolaritySplit
backGroundRate = 30             # default rebuild rate for this card (0-100)
stripeSize = 7                 # default LD strip size (per DDF: 4=8K, 5=16K, 7=64K, 11=1MB, etc.)
flushTime = 4                  # default cache flush time in seconds
cachedIo = 0                   # default LD is cached
writeBack = 1                  # default LD is WriteBack (0=WT, 1=WB, 2=Adaptive)
readAhead = 0                  # default LD read-ahead policy (0=none, 1=RA, 2=Adaptive)
cacheWhenBbuBad = 0            # default LD setting for enabling WB when BBU bad - 1=enable WB even when BBU bad
smartMode = 0                  # default smart mode (0=mode 6, 1=disable, 2=mode 2)
alarmDisable = 1               # default alarm to disabled if set
coercion = 0                   # 0=none, 1=128M, 2=1G, 3=reserved
zcrConfig = 0                  # ZCR configuration data (0=unknown, 1=RADIOS, 16-31=IDSEL for ZCR)
dirtyLedShowsDriveActivity = 0 # 1=change dirty LED to show drive activity
biosContinueOnError = 1        # 1=continue BIOS boot on error - default
spindownMode = 0               # drive spindown mode on shutdown (0=none, 1=internal only, 2=external only, 3=all)
allowedDeviceTypes = 0         # 0=SAS/SATA mix, 1=no SATA(SAS only), 2=no SAS(SATA only)
allowMixInEnclosure = 1        # allow SAS/SATA mix within an enclosure
allowMixInLD = 0               # allow SAS/SATA HDD mix within an LD
allowSSDMixInLD = 0            # allow SAS/SATA SSD mix within an LD
allowMixSSDHDDInLD = 0         # allow SSD/HDD mix within an LD
allowSataInCluster = 0         # allow SATA drives to be used in a cluster configuration
maxChainedEnclosures = 3       # maximum number of enclosures that may be chained
disableCtrlR = 1               # 1=disable Ctrl-R configuration utility, 0=enable Ctrl-R utility
enableWebBios = 1              # 1=enable WebBIOS configuration utility, 0=disable WebBIOS utility
phyPolaritySplit = 0           # polarity for TX/RX pair is different (bitmap...0=RX/TX same, 1=RX/TX different; phyPolarity.x=RX)
directPdMapping = 1            # 1=enable direct PD mapping, 0=persistent PD mapping
biosEnumerateLds = 1           # 1=BIOS to display LDs at POST
restoreHotSpareOnInsertion = 1 # HSP kicks in, insert the failed drive, it becomes HSP
exposeEnclosureDevices = 0     # 1=device driver should expose enclosure devices, 0=hide enclosure devices
maintainPdFailHistory = 1      # 1=enable tracking of bad PDs across reboot; will also show failed LED status for missing bad drives
disablePuncturing = 1          # 1=Don't puncture LBA's in PD's. 0=okay to puncture. This is for SAS drives
zeroBasedEnclEnumeration = 0   # 1=Enclosure enumeration start with Zero. 0=Enclosure enumeration start with One.
disableBootCLI = 1             # 0=enable pre boot CLI tool, 1=disable pre boot CLI.
quadPortConnectorMap = 0       # Bitmap defining connector map for 8 quad-ports, 0=Internal connector/unused, 1=External connector/SAS MUX control.
driveActivityLed = 1           # 0=No LED for drive activity, 1=Show all drive activity.
disableAutoDetectBackplane = 0 # 0=SGPIO/i2c SEP enabled, 1=disable auto detect SGPIO,2=disable i2c SEP auto detect,3=disable both auto detect.
useFdeOnly = 0				   # 0=FDE and controller encryption (if HW supports) is allowed, 1=Only support FDE encryption, disallow controller encryption.
enableLedHeader  = 1		   # 0=No LED for drive faults, 1=enable LED for drive faults.
delayPOST = 0                  # intentional delay to be introduced during FW POST. Possible coded values: 0 to 7,which gives a value of 0,15,30,45,60,75,90,105 seconds
subVendorId=0x1033                # sub-vendor ID for this board
subDeviceId=0x836e                # sub-vendor ID for this board
